Oil Seal Suppliers in UAE | Sizes, NBR & Viton, SC/TC | Myra
Oil seals supplier and sourcing support for UAE buyers (Dubai, Sharjah, Ajman). We quote based on specifications such as ID x OD x width, lip type (SC/TC), material (NBR/Viton/PTFE), and shaft speed so your replacement seal fits the housing and shaft without rework.
Share oil seal size in mm (ID x OD x width), application, and media/temperature. We verify oil seal dimensions, profiles, and materials against common standards so procurement teams avoid rework, leakage, and downtime.
Trust signals
- Quotes same business day
- Specification checks before supply
- UAE supply coverage
Quick references for sizing, identification, and materials.
Browse Brand-Specific Oil Seals Options
Use these brand-category pages to compare capability fit before submitting your RFQ.
Send These Details for the Fastest Quote
- ID x OD x width in mm (e.g., 25x47x7).
- Seal type (TC/SC), lip count, and spring-loaded or not.
- Material (NBR/FKM/EPDM/PTFE) + media + temperature.
- Shaft speed (RPM) if high-speed.
- Photo of seal markings or housing/shaft if available.
Oil Seal Types We Supply
Profiles differ because speeds, shaft finishes, contamination levels, and media vary. Choosing the right profile reduces wear and improves service life.
Single-Lip (SC) Oil Seals
Single sealing lip for standard oil retention in cleaner environments.
- Gearboxes
- Pumps
- Electric motors
- General rotating equipment
- ID x OD x width
- SC lip type
- Material + media
- Temperature range
Double-Lip / Dust Lip (TC) Oil Seals
Primary oil lip plus dust lip for contamination-heavy environments.
- Construction equipment
- Compressors
- Outdoor drives
- Dusty plants
- ID x OD x width
- TC lip type
- Media + temperature
- RPM if high speed
Metal-Cased OD Oil Seals
Rigid OD for stable fit in metal housings and heavy-duty duty cycles.
- Gearboxes
- High-load pumps
- Industrial reducers
- ID x OD x width
- Housing bore
- Material + media
- Lip type
Rubber-Covered OD Oil Seals
Elastomer OD improves sealing in light corrosion or minor bore wear.
- Motors
- Pumps
- Maintenance replacements
- ID x OD x width
- Bore condition
- Material + media
Spring-Loaded Lip Seals
Spring maintains lip contact for higher speed or variable conditions.
- Gearboxes
- High-speed motors
- Pumps
- ID x OD x width
- Spring-loaded
- RPM
- Material + media
Non-Spring Lip Seals
Simpler lip design for low-speed or grease-sealed applications.
- Low-speed reducers
- Lubricated bearings
- MRO replacements
- ID x OD x width
- Non-spring
- Media + temperature
Material Selection for Media and Temperature
Typical ranges are shown for guidance. Final selection depends on shaft speed, temperature, and media exposure.
NBR (Nitrile)
Typical -30C to +100CNBR oil seal material for mineral oils, fuels, and greases.
- Gear oil
- Hydraulic oil
- Lubricating grease
FKM (Viton)
Typical -20C to +200CViton oil seal (FKM) option for higher temperature and chemical resistance.
- Hot oils
- Fuels
- Mild chemicals
EPDM
Typical -40C to +120CBest for water, glycol, and steam-compatible duties.
- Water
- Glycol
- Mild chemicals
Note: Not compatible with mineral oils.
PTFE
Typical -60C to +250CLow friction option for aggressive media or higher shaft speeds.
- Aggressive chemicals
- Dry-running or high-speed use
Oil Seal Specification Table
| Parameter | Options / Notes |
|---|---|
| ID (shaft diameter) | Measured shaft diameter in mm or inches. |
| OD (housing bore) | Bore size and housing condition for interference fit. |
| Width | Seal width required to match housing depth. |
| Lip type | Single, double, or dust lip (SC/TC). |
| Material | NBR, FKM (Viton), EPDM, PTFE based on media and temperature. |
| Spring type | Spring-loaded or non-spring depending on speed and duty. |
| Rotation direction | Bi-directional or directional based on lip design. |
| Housing considerations | Bore tolerance, surface finish, and corrosion condition. |
| Speed and temperature | Depends on design/material. Share RPM and temperature for confirmation. |
Reduce Back-and-Forth on Oil Seal RFQs
Oil seal sizes are specified as ID x OD x width, plus seal type, material, and media details so we can confirm fit before supply.
- ID x OD x width in mm (e.g., 25x47x7).
- Seal type (TC/SC), lip count, and spring-loaded or not.
- Material (NBR/FKM/EPDM/PTFE) + media + temperature.
- Shaft speed (RPM) if high-speed.
- Photo of seal markings or housing/shaft if available.
- 25x47x7 mm, TC, NBR, gear oil, 60C.
- 40x62x10 mm, SC, FKM (Viton), pump duty, 120C.
- 50x72x8 mm, rubber-covered OD, spring-loaded, gearbox.
- 70x90x10 mm, EPDM, water/glycol, 80C.
Avoid These When Ordering Oil Seals
- Providing OD without width or ID
- Missing lip type (TC vs SC)
- Not stating media or temperature, leading to wrong material
- Reusing a worn shaft without a sleeve
- Assuming housing tolerances without checking bore condition
- Choosing the right size but wrong profile or lip style
Why Myra for Oil Seals in UAE
- Dimensional verification (ID/OD/width) before quoting.
- Profile matching to shaft and housing conditions.
- Material selection guidance for media, speed, and temperature.
- Equivalent sourcing to balance lead time and budget.
- UAE supply support for project and MRO requirements.
Buyer Questions on Oil Seals
SC is a single-lip oil seal for cleaner environments, while TC adds a dust lip for contamination protection.
NBR suits standard oils at moderate temperatures. FKM (Viton) handles higher heat and more aggressive media. Share media and temperature for confirmation.
Use ID x OD x width (e.g., 25x47x7 mm) and include the lip type (TC/SC) and material.
Share the old seal photos or markings and the application details. We match lip profile to contamination level and duty.
Yes. Send seal markings or a clear photo so we can confirm the profile and size.
If the shaft surface is worn or grooved, a sleeve protects the new seal and extends service life.
We carry common sizes and can source non-standard sizes quickly. Share your size and profile for lead time confirmation.